See all the robots

PUDU CC1

A cleaning shift as a single task

The CC1 sweeps, scrubs, vacuums and dries in one pass. It comes in two versions: the original and the Pro, which sees the dirt and checks what it cleaned. We configure the routes and the schedule, and the floor gets done without anyone pushing a machine.

The PUDU CC1 floor-cleaning robot seen from behind, with the squeegee, the brush deck and the side brush in view.
  • Sweeps
  • Scrubs
  • Vacuums
  • Dries

Two versions, the same cleaning

Both do the same four kinds of cleaning in one pass. The difference is whether the machine follows its route, or also sees the floor and responds to what it finds.

The PUDU CC1, white and lime green, seen from the front.

CC1

The original

  • The dirt is regular and a fixed route is enough to deal with it.
  • Reports of time and area are enough to follow the cleaning.
  • You want the four cleaning functions in one machine.
The PUDU CC1 Pro, dark grey, seen from the front.

CC1 Pro

With AI vision

  • There are spills and stains that turn up during the day.
  • The floor changes from area to area, from hard floor to carpet.
  • You want to see where the dirt was and what was left behind.

Seen up close

Three things a datasheet does not show.

It reaches the skirting

The brush works hard against the wall, so the corner is not left for someone to sweep afterwards.

It lifts what is on the floor

Under the machine the roller frees the dirt and the suction takes it, in the same pass.

It charges and comes back

With the battery low it heads for the dock on its own and returns to where it left off.

A day of work

This is what happens once we have configured the routes. Every day, at the same time, with nobody giving the order.

  1. 01

    It leaves on schedule

    The route and the schedule are set during installation. The robot starts on its own, with nobody having to go and fetch it.

  2. 02

    It covers the floor in passes

    It works the area in parallel passes to the end. What is behind it is clean and dry.

  3. 03

    It sorts itself out and carries on

    If the battery or the water runs out part way, it returns to the dock, deals with it and resumes the route where it stopped.

  4. 04

    It finishes and leaves a record

    At the end it returns to the dock. You are left with a record of what it did, how long it took and what it could not reach.

The shift fits in a phone

No need to go and look: you know what is done, and you can stop it without leaving where you are.

  • See them all at once

    Which machine is scrubbing, which is charging, how much water it has left and how much battery.

  • The route is drawn once

    The route, the starting point, the virtual walls and the zones it does not enter. Set at installation, and it stays set.

  • Start it, stop it, tune it

    Begin a task, interrupt it or send it to charge, and adjust the brush and the suction without walking to the robot.

The screens are from PUDU Robotics' own app. At installation we leave your team using it.

On the CC1 Pro

It sees the dirt and decides what to do

The CC1 Pro adds cameras and artificial intelligence to the same cleaning base. Instead of only following its route, it responds to what it finds.

A CC1 Pro in a shop aisle, with the area of a stain marked on the floor ahead of it.

Straight to the stain

During its round it recognises coffee spills, sauces or puddles and plans the shortest way to them.

A CC1 Pro cleaning a supermarket aisle between freezer cabinets.

It adjusts to the floor

It cleans harder on stubborn stains, saves water and energy where the floor is already clean, and switches to vacuum only when it reaches a carpet.

The back of the CC1 Pro, its rear camera beam analysing the floor and a warning over a patch left to clean.

It checks its own work

A camera at the back sees the floor it has just cleaned. If something is left it goes back, and at the end of the task it marks what needs attention.

On the CC1 Pro

What the cleaning leaves on record

At the end of each task the CC1 Pro shows where the dirt was, what survived several passes and how the operation is running.

An app screen with the map of the space and the record of the dirtiest areas.

Where the dirt builds up

A map of the areas with the most waste and of the stains that survived several passes, to plan cleaning and inspection.

An operations dashboard with the indicators for cleaning tasks and maintenance.

How the operation is running

Tasks run and completed, maintenance and fault alerts, in one dashboard.

The CC1 in numbers

The figures the manufacturer publishes for both versions. Where they differ, each has a column of its own.

  • 700 to 1000m²/hFloor cleaned per hour, full coverage
  • 15 + 15LClean and waste water tanks
  • 5hRun time scrubbing
  • 1.2m/sTop speed
Further specifications of the PUDU CC1 and the PUDU CC1 Pro
CharacteristicCC1The originalCC1 ProWith AI vision
Cleaning functionsSweeping, scrubbing, vacuuming and mopping
Spot cleaning of stainsNone1500 to 3000 m²/h
Run time vacuuming carpet4 h
Run time silent mopping9 h
Charging timeUnder 3 hAbout 3 h
Noise while cleaningUnder 70 dB(A)Not published
SuctionUp to 17,000 PaNot published
Minimum gapNot published70 cm

Figures published by PUDU Robotics and checked by us on 16 November 2026. For the full datasheet of either version, talk to us.

Where it makes the most difference

Large areas, long opening hours, and a floor that cannot wait until the end of the day.

Choose the space

Want to see the CC1 in your space?

A short visit is enough for us to tell you which version fits, what routes and schedule it would run and what it costs.